Exseed Dabcool W2 Second Generation Kit 1500mAh Water Pipe Vaporizer Kit

Exseed Dabcool W2 Second Generation Kit

• Brand: Exseed
• Unit: set
• Type: Vaporizer
  
• Net Weight: 710(g)

The combined shipping cost will be calculated automatically by the system after you choose the shipping destination in the checkout step.

Exseed Dabcool W2 Second Generation Kit has been upgraded to a larger size and better performance, especially as it is the first waterproof atomizer on the market to pass the IPX4 test and has passed the 10,000 times thermal expansion test, making it more waterproof and heat resistant. Exseed II has a built-in 1500mAh battery for faster heating and more precise temperature control. Exseed II atomizer effectively prevents the coil from coming into contact with water and the built-in coil can be easily replaced without having to replace the entire atomizer.

Features

▪ Compatible With Dabcool W2 Atomizer and Dabcool W2 V2 Coil

▪ IPX4 Waterproof Atomizer, Cannot Be Immersed

▪ New Program, More Accurate Temperature Control

▪ Replacement Amotizer Coil, Comes With 1 Atomizer And 1 Coil

▪ New Atomizer Structtion, Longer Life, More High Performance

1* Alcohol Pad

1* Micro-USB Super Charger

1* Loading Tool

1* Glass Attachment

1* Atomizer

1* Replaceable Coil

1* Silicone Box

1* Carb Cap

2* Extra Bowl

STEP 1: Fully charge the device before first use. White lights pulse while charging, and turn off automatically when complete.（1 light: 0-25%; 2 lights: 25-50%; 3 lights: 50-75% ; 4 lights: 75-100%）

STEP 2: Fill glass with water just above the air-hole. Do not fill glass while attached to the base.

X- Do not allow water in the lower section!

STEP 3: Align the inlet hole on the front of the glass with an atomizer. Carefully place the glass into the base.

STEP 4: Hold the button for 3 seconds to turn on the device (same way to turn off the device). The white lights will flash once and the ambient lights will flash sequentially red>blue>green.

STEP 5: Single click to toggle through heat settings.

1 white light: 450℉ 2 white lights: 500℉

3 white lights: 600℉ 4 white lights: 680℉ The device will vibrate once while changing heat.

STEP 6: Use Loading Tool to place contents on the bottom surface of the bowl [not the side].

STEP 7: Place carb cap on top of the atomizer.

STEP 8: Double click to initiate heat-up [5 seconds avg. ], the device will vibrate twice and ambient lights will be red. Single-click the button to turn off the heat-up process at any time.

STEP 9: Ambient lights will turn green when ready. ( green lights will be on for 20 seconds, then heat up process automatically stop and ambient lights turn blue)

STEP 10: Use a cotton swab to clean the chamber after each use.

Allow chamber to fully cool before touching.

Be sure the device is powered off before cleaning.

After cleaning, allow all parts to thoroughly dry before using.

Do not blow into the glass when filled with water and attached to the base.

Do not overfill! glass with water.

Do not overfill the chamber.

Wait 1 minute between uses.

1. To check battery life: click the button 3 times, and white lights will flash 3 times.

1 light: 0-25%; 2 lights: 25-50%;

3 lights: 50-75% ; 4 lights: 75-100%

2. When an atomizer is not placed or not connected well, ambient lights will flash sequentially red>blue>green then turn off.

3. Low voltage protection: when the input voltage is under 6.4V, ambient lights will flash red 3 times. when the input voltage is under 6.0V, ambient lights will flash red 3 times then the device will automatically turn off.

4. Short circuit protection: white lights will flash 5 times.

5. Overheating protection: ambient lights will be red for 5 seconds.

6. The device can be used while the battery pack is charging.

Attention: As the manufacturer needs the serial number to provide a replacement, we highly recommend you keep the original packing box or take picture of the code before discarding it. Thank you!